Step1
第1步：要求
Torx 6 Screwdriver
6六角螺丝起子
Small straight-slot screwdriver
小直槽螺丝
Credit card or guitar pick
信用卡或吉他挑
Toothpick
牙签
Small knife
小刀
Step 2: Remove peripheral components
步骤2：删除外围元件
Remove all of the loose parts like the battery, sim card and memory card.
删除，如电池，SIM卡和内存卡上的松散各地。
Step 3: Unscrewing
第3步：螺牙
Take out the 8 screws from the handset, keep them in a safe place to avoid loosing any of them.
从手机取出8个螺丝，在一个安全的地方，使他们避免失去任何人。
Step 4: Remove lower support
第4步：删除较低的支持
Remove the lower part of the phone that has small connectors to the PCB an
d is half-glued to the back cover.
删除的手机已连接到PCB小，是半粘在后盖下部。
Use a small knife to pierce once under both sides of the handset.
用小刀刺穿根据双方的手机一次。
You should now be able to lift it open with your own finger nails.
您现在应该可以解除它打开自己的指甲。
Step 5: Create a gap between covers
第五步：创建一个涵盖差距
Starting at the top, use a guitar pick to create a small gap between the back and front covers.
开始在顶部，使用吉他之间创建一个选择的背部和前的小差距封面。
Be patient and don't use a knife otherwise the faux-chrome will start to peel off.
要有耐心，不要用刀子否则人造铬会开始脱落。
Once the gap is big enough use a credit card (that is slightly thicker than the guitar pick) to force the upper end of the back cover off its clips.
一旦差距足够大使用信用卡（即比选较厚的吉他），以迫使其关闭后盖剪辑的上端。
The smooth plastic should prevent the handset getting scratched.
光滑的塑料应防止手机越来越划伤。
Step 6: Create gap on right side
第6步：创建差距在右侧
Continue creating the gap on the right side.
继续创建右边的差距。
Start slowly from the front cover and stick the credit card between the housing parts.
开始慢慢地从封面和坚持之间的房屋部分信用卡。
The first clip should now be open but continue until you are on the lower right side.
第一个剪辑开放，但现在应该继续下去，直到你在右下侧的。
Be careful not to pierce too deep with the credit card, otherwise there is a chance of cutting the ribbons beneath.
小心不要刺破太深刻的信用卡，否则有一个削减下缎带的机会。
Now release the lower clips as you did for those at the top of the housing.
现在释放低剪辑为您在房屋顶部的一样。
Step 7: Loosen left side
第七步：松开左侧
At this point, the right side and bottom should be loosened.
在这一点上，右侧和底部应该放松。
The clips on the left side are too tight to get a credit card through.
在左侧的剪辑太紧获得通过信用卡。
However, this is not needed, if you lift the back cover slowly and wiggle it a little it should come off by itself.
然而，这是不必要的，如果你提起后盖慢慢蠕动这一点是应该由自行关闭。
Note that this step may require a bit of force to open properly.
请注意，此步骤可能需要一些武力打开正常。
Step 8: Prepare to remove sim and memory card holder
步骤8：准备删除SIM卡和存储卡持有人
Now you need to remove the sim and memory card holder that has four clips.
现在，您需要删除的SIM卡和存储卡持有人即有4个片段。
Two of these clips can be seen in the picture below (where the screwdriver is pointing to).
这些片段可以看到两个在下面的图片（如螺丝刀指向）。
Use a toothpick to lever between the PCB and clip from underneath.
使用牙签，以杠杆之间的PCB和剪辑从下面。
Now do the same to the two clips on the other side.
现在这样做对对方的两个片段。
DO NOT REMOVE THE HOLDER YET.
请勿移除持有人呢。
Take a closer look at the next picture first.
请看下一张图片仔细看看。
Step 9: Remove holder
第9步：删除持有人
A ribbon sits underneath the holder so you have to be careful not to rip it.
阿丝带坐在所以你必须要小心，不要把DVD录制下的持有人。
Lift the holder a little from the right side and use a toothpick to lift it off.
电梯从右边一点点持有和使用牙签解除其关闭。
Step 10: Remove audio jack
第10步：删除音频插孔
The picture below shows the ribbon again.
下图显示了剪彩了。
Take off the audio jack by simply lifting it with your fingers.
起飞只需用手指解除它的音频插孔。
The arrow shows you in which direction.
箭头显示你在哪个方向。
Step 11: Remove ribbons
第11步：删除丝带
Now loosen the three ribbons at the lower end of the PCB.
现在放松在印刷电路板下端的3个缎带。
Use a toothpick, guitar pick or credit card to remove these ribbons that should come off easily.
使用牙签，挑吉他或信用卡，以消除这些彩带，应该容易脱落。
Do not remove any of the SMD components beside these ribbons.
不要删除这些缎带旁边的贴片组件。
If you do, it will require you to re-solder them back.
如果这样做，它会要求您重新焊回。
Step 12: Remove additional ribbon
步骤12：删除额外的丝带
Remember to remove another ribbon that sits underneath the audio jack.
请记住，删除另一丝带，坐在下面的音频插口。
The red screwdriver is pointing to it in the picture below.
红色起子指向它在以下图片。
Step 13: Remove PCB
第13步：删除电路板
Now you need to loosen the clips that the PCB is attached to on the front cover.
现在你需要放松的，该电路板连接到封面剪辑。
The PCB is attached via four clips.
PCB的连接通过四个片段。
Use the straight-slot screwdriver to pierce between the PCB and upstanding part of the front cover.
使用直槽螺丝刀刺穿之间的PCB和正直的前盖部分。
The screwdriver should be placed at a direct angle from the side (see the picture from step 15).
螺丝刀应该放在直接从侧面的角度（见照片从第15步）。
Now wiggle a little and the PCB should jump out of the clips.
现在有点摆动和PCB应该跳出剪辑。
Repeat this on the other three clips.
重复这对其他三个片段。
You should now be able to lift the lower end of the PCB and pull it out in a flat angle.
您现在应该可以解除低端的PCB拉在一个平面的角度出来。
Step 14: Separate display and touch module
步骤14：单独的显示和触摸模块
Now you will need to split the display, touch module and front cover.
现在，您将需要分割显示，触摸模块和前盖。
Loosen the keypad, but be careful not to tear the ribbon.
松开键盘，但要小心，不要撕裂剪彩。
Step 15: Remove copper-coloured ribbons
步骤15：删除铜彩带
Slowly pierce underneath the copper looking ribbons.
慢慢地寻找带刺下的铜。
They are glued to the whole area.
他们是粘到整个地区。
After you've cut a few parts you should be able to remove the ribbons with your fingers, start with the biggest and finish with the smallest one.
在您节省几件你应该能够消除与你的手指，启动拥有最大和最小的一个完成的缎带。
Step 16: Remove display
步骤16：删除显示
The display is also clipped in the same way that the PCB was.
该显示器还夹在相同的方式，在PCB了。
Once you've used a credit card to remove the clips it should pop off by itself.
一旦您使用信用卡，以消除它的剪辑应该弹出的自行关闭。
That's it you've now successfully disassembled the Xperia X10.
这就是它，你现在已经成功地拆解的Xperia X10。
因篇幅问题不能全部显示，请点此查看更多更全内容